3x3x3 LED Cube Arduino Shield Directions

Build Your Own
3x3x3 LED Cube Arduino Shield
DSC_0140
This is what you’ll get in the end.
Have fun!

DSC_0157What should be in your kit:
1 – PCB
27 – LED’s
2 – 6 Pins for Arduino
2 – 8 Pins for Arduino
3 – Resistors
1 – Foam Guide
1 – Small Wire
1 – Medium Wire
1 – Large Wire
You will need: Solder Iron, Solder, Wire Cutters, Wire Strippers, Safety Googles, Helping hands are always good (but not manditory) and a really GREAT ATTITUDE!!!

In the below pictures I will be switching between RED LED’s and GREEN LED’s. My mom made a GREEN one…some parts didn’t turn out so good. She did try – and she is a VERY beginner! Good Job Mom!
Have FUN!

Little Information first

LED’s: All LED’s have a Positive (+) and a Negative (-) As you can see on the picture below. The Positive (+) is longer than the Negative (-) You will always be bending the Negative (-). The official term for the Negative is “Cathode” and for the Positive is “Anode” For these directions we will use short and long.
DSC_0158led_anode_cathode

Testing your LED’s: I’ve tested every single LED. However if you’d like to test to make sure…here’s how to do it. Take a Lithium battery, stick the LED with the long led on the side of the battery marked with a "+". Press the Leds against the battery. The light should turn on. If not…you’ve got yourself a bad LED.
DSC_0233DSC_0234DSC_0235

Guide Sheet: I used this as my template. If you ever get confused (easy to do) refer back to the guide sheet. This will tell you how to bend and placement of the LED’s.
DSC_0230
Each circle has 2 dots. The one with the arrow is the Negative (-) and the one standing alone is the Positive (+). This shows you which way to bend your Negative (-) led.

Connecting your LED’s

Lets get started…..
DSC_0160
This is an enlarged picture to show using the Helping Hands.

DSC_0160 DSC_0164DSC_0168
ALWAYS FOLD DOWN THE NEGATIVE (-)..SHORTER SIDE
1) Start with the center hole. Folding down Negative (-) on the right side.
2) Place the second LED in as shown. Solder them together. Don’t worry about the end of the LED being too long. We will be trimming them.
3) Place the third LED in as shown. Solder them together.
Continue on until all 9 LED’s are soldered together.

DSC_0183
Before cutting the extra wire. Take another look to make sure all your LED’s are going the correct way and you folded down the Negative (-) This is the time to catch a mistake…you can always unsolder and fix it.
Using your wire cutters, cut off the extra wire. Mostly should be on the 4 corners.
You should have.. (3) 9 pin LED’s squares

DSC_0186

Solder all 3 levels together

Now the tricky part starts. Stacking them together.
DSC_0198
Put one LED piece back into the foam. You can find something to slide in between as shown.

DSC_0200
Put your 2nd layer on. You will be soldering the Positive (+) to the Positive (+) on the next layer as shown. You may need to bend the wires so they meet. *Please note that the picture above is showing how to stack the layers. It has not been soldered together. If you connect one Positive (+) to a Negative (-) your LED will not light up in the end.

DSC_0204
Do the same with the 3rd layer. *Please note that the picture above is showing how to stack the layers. It has not been soldered together.

DSC_0098
This is what you should have in the end. This is the one my mom did…alittle crooked, but that’s ok. As long as all the soldering is good the LED’s will still shine.
Set your LED “Cube” off to the side. Let’s work on the PCB.

Resistors

projects 006
Carefully take the tape of the ends.

DSC_0188
The Resistors come straight. You need to bend as shown. There is not (+) (-) to these, so you don’t have to bend a correct wire. Just bend either one down.

DSC_0189
Place each resistor into the board. Solder each in on the back of the PCB. There is no right or wrong way for these. I prefer to have mine going in the same direction.

3 Black Wires

DSC_0195projects 044
You will need to take your Wire Strippers and strip off a bit at each end. You will be soldering the top and the bottom, so strip off enough to do so. You may also choose to strip off all the black. Either way is fine.

projects 052
Place the wires in each hole starting with the smallest and working up to the tallest.
Small (1st hole) Medium (2nd hole) Large (3rd hole)
Solder on the backside.

Put the whole shield onto the PCB

Almost finished….Let’s put the Cube onto the PCB. This part is also tricky, just take your time. It will work in the end!

Untitled 0 37 26-19Untitled 0 37 28-09projects 038
1) Picture is showing that there are 2 holes…you only have 1 wire…
2) Picture is showing which hole you should use.
3) Picture is showing the wires in the correct hole.
You can flip the PCB over and you will notice that only one of the holes on back have a connection.

Untitled 0 37 12-48Untitled 0 38 43-11
Take your time and get each wire into the correct hole. It’s kinda like a puzzle. Once you’ve succeed in doing that, solder the wires in place on the back side. Then give yourself a pat on the back!

Make the connection with your black wires

Look at your black wires. You need to solder each of them to the correct level. First look for the very first LED you but into the foam. Picture below. This is the wire you will solder to the Negative (-).
Solder your short black wire to the negative (-) LED.
Solder your medium black wire to the negative (-) LED on the second level.
Solder your long black wire to the negative (-) LED on the top level.

DSC_0214DSC_0160114823-magic-marker-icon-arrows-arrow-styled-leftFirst LED into the foam.

You may have some extra wire. I couldn’t get my wire cutters into the cube – so I left mine alone.

Arduino Pins

DSC_0157
As you can see there are 2 with 6 pins and 2 with 8 pins.

DSC_0157
If you look on your PCB one side will have 2 – 6 pin slots and the other side will have 2 – 8 pin slots.
You will be soldering them in on the bottom. You WILL NOT cut off the extra wire. That wire is used to hook into your Arduino.

DSC_0143
This is what your Arduino Pins should look like.

Your Arduino

Hook your new 3x3x3 Cube Arduino Shield into your Arduino. Be careful. Keep an eye on your pins lining them up perfect. If you didn’t solder them in just right, you may need to bend them a bit. It may be hard hooking them together the first couple of times.

DSC_0220

Connecting your Arduino to computer

Connect your Arduino to your computer. Install the test code,  http://lookwhatjoeysmaking.blogspot.com/p/3x3x3-codes.html. You can also find this under the 3x3x3 Codes tab on the main page of my website.
 You should see all the LEDs go on. I usually take mine into the bathroom – nice and dark!

projects 001
Try more codes…make your own. Take some pictures and share.
Have fun and be patient.

Credit given to Mitch Altman
http://creativecommons.org/licenses/by-sa/3.0/